Furnace Repair in Memphis, IN
A furnace usually gives you a little warning before it quits—odd noises, short cycling, uneven heat, or a house that never quite reaches the thermostat setting. But when it finally stops working on a cold Indiana night, the situation turns urgent fast. If you’re searching for furnace repair in Memphis, IN, the goal is simple: restore safe, steady heat without guessing games.
At Mitch Craig Heating & Cooling in Memphis, IN we provide heating and furnace services including installation, preventative maintenance and repair. We’re here to help you understand what’s happening, what to check safely, and when it’s time to call in a professional.
What should I do first if my furnace stops working?
If your furnace stops working, first check the thermostat settings, replace a dirty air filter, and verify the circuit breaker hasn’t tripped. If you smell gas, see signs of overheating, or the furnace won’t restart after basic checks, turn the system off and call a licensed HVAC technician for professional furnace repair. (Safety guidance around furnace issues commonly emphasizes basic checks and calling a pro when hazards are possible.)
Why Furnace Repair in Memphis, IN Should Start With Safety
When heat goes out, it’s tempting to troubleshoot aggressively. We recommend a safer approach: confirm the basics, avoid anything involving gas lines or internal electrical components, and focus on getting expert help when warning signs appear.
Stop and call right away if you notice:
-
A gas smell or “rotten egg” odor
-
Soot, scorch marks, or burning smells
-
Repeated shutting off right after ignition
-
Headaches, dizziness, nausea, or symptoms that could be related to combustion issues
-
Carbon monoxide alarm activation
If any of these are present, shut the system off and contact a professional immediately. (Consumer safety resources commonly stress leaving gas and combustion concerns to professionals.)
Heating Repair in Memphis, IN: Common Furnace Problems We See
Most furnace breakdowns fall into a few predictable categories. Knowing the “usual suspects” can help you describe symptoms clearly when you call—so repairs go faster.
1) Dirty or clogged air filter (restricted airflow)
A clogged filter can cause overheating, poor airflow, and shutdowns. It’s one of the simplest issues with the biggest impact.
2) Thermostat issues
Sometimes the furnace is fine—but the thermostat isn’t sending the right signals (low batteries, incorrect settings, or calibration issues).
3) Ignition or flame-sensing problems (gas furnaces)
If the furnace starts then shuts off quickly, the flame sensor or ignition components may be involved.
4) Electrical or control board problems
Modern furnaces rely on control boards and safety switches. Electrical issues can prevent startup or cause intermittent operation.
5) Blower motor/capacitor issues
If the furnace runs but airflow is weak—or you hear a humming or squealing sound—the blower components may be struggling.
6) Short cycling (turning on and off too frequently)
Short cycling can come from overheating, airflow restriction, thermostat placement issues, or failing components.
Emergency Furnace Repair in Memphis, IN: When It’s Not “Wait Until Morning”
Some heating problems can wait a day. Others can’t. If you’re dealing with any of the following, it’s time to treat it as urgent:
-
No heat and temperatures dropping rapidly inside the home
-
A furnace that repeatedly tries to ignite and fails
-
Burning smells, visible soot, or signs of overheating
-
The system shuts down and won’t restart
-
You have infants, seniors, or vulnerable household members who need stable indoor temperatures
Our team offers 24-hour emergency repair services as part of our heating and furnace service offerings.
Gas Furnace Repair in Memphis, IN: Symptoms That Often Point to Combustion or Ignition Issues
Gas furnaces are efficient and dependable—when all safety systems and ignition components are functioning properly. If your gas furnace is acting up, these are common symptoms we hear:
-
Furnace clicks, starts, then shuts off quickly
-
Pilot/ignition problems (system attempts but won’t light)
-
“Cold air” or lukewarm air from vents after startup
-
Unusual odors near the unit
-
Frequent shutdowns, especially shortly after ignition
Because combustion is involved, we recommend avoiding DIY repairs beyond basic thermostat and filter checks. For anything ignition-related, professional diagnosis is the safest path.
Electric Furnace Repair in Memphis, IN: What’s Different?
Electric furnaces don’t burn fuel, but they can still fail due to:
-
Electrical component wear (relays, sequencers, breakers)
-
Blower issues
-
Thermostat or wiring problems
-
Heating element failures
If your breaker keeps tripping, don’t reset it repeatedly—recurring trips can indicate a real electrical fault that needs professional evaluation.
Furnace Not Blowing Hot Air in Memphis, IN: Safe Things to Check First
This is one of the most common “People Also Ask” questions—and it’s often fixable with basic checks.
Before you call, here are a few safe steps:
-
Check the thermostat
-
Set it to “Heat”
-
Raise the temperature 3–5 degrees above room temperature
-
Replace thermostat batteries if needed
-
-
Check the air filter
-
If it’s clogged or very dusty, replace it
-
-
Confirm power
-
Check the furnace switch (looks like a light switch)
-
Check the circuit breaker panel
-
-
Look for blocked vents
-
Make sure supply/return vents aren’t covered by furniture or rugs
-
If those steps don’t restore heat, it’s time for professional diagnosis—especially if the system starts and stops quickly, makes unusual noises, or shows error codes.
What Does Furnace Repair Cost in Memphis, IN?
This is another frequent question, and we’ll be straightforward: the cost depends on what failed. A thermostat issue is very different from a motor replacement or an electrical control problem.
Pricing typically varies based on:
-
The failed part (sensor vs. motor vs. control board)
-
Furnace type (gas, electric, high-efficiency)
-
System accessibility (tight crawlspaces, attic installs, etc.)
-
Whether service is needed during off-hours
The best way to get accurate numbers is an on-site diagnosis. We’ll identify the issue and explain repair options clearly, so you can make an informed decision.
How Long Does Furnace Repair Take?
Many furnace repairs can be completed in a single visit once the issue is diagnosed. Timing depends on:
-
The complexity of the problem
-
Whether parts are immediately available, most parts are
-
Whether there are multiple contributing issues (like airflow + a failing component)
When we arrive, we focus on accurate diagnosis first—because replacing parts without confirming the real cause is how homeowners end up paying twice.
Furnace Troubleshooting vs. Furnace Service: What Homeowners Should and Shouldn’t Do
We’re big believers in homeowner education—especially when it helps you avoid an unnecessary service call. Our website even offers support resources and troubleshooting information to help customers.
Safe homeowner checks:
-
Thermostat settings and batteries
-
Replacing the air filter
-
Checking breakers and the furnace switch
-
Ensuring vents are open and unobstructed
Leave these to professionals:
-
Anything involving gas, burners, or ignition components
-
Control board/electrical component replacement
-
Internal safety switches and diagnostics
-
Refrigerant or heat pump-related work (if your heating is part of a heat pump system)
Furnace Repair or Replace in Memphis, IN: How to Know Which One Makes Sense
At some point, every homeowner asks: “Should I fix this furnace or replace it?”
We help customers work through that decision with practical factors like:
-
Age and condition of the system
-
Frequency of repairs
-
Severity/cost of the current repair
-
Comfort and efficiency issues
-
Long-term plans for the home
We also provide educational guidance on the “repair or replace” decision for heating equipment on our site.
A good rule of thumb: if repairs are becoming frequent and comfort is inconsistent, it may be time to discuss replacement options—especially before a mid-winter emergency forces a rushed choice.
Furnace Maintenance in Memphis, IN: The Best Way to Avoid Surprise Breakdowns
Most emergency breakdowns don’t come out of nowhere. They build up: dust, wear, loose electrical connections, and airflow problems that strain components.
Routine maintenance helps you:
-
Catch failing parts early
-
Keep airflow and performance steady
-
Reduce mid-season shutdowns
-
Extend system life
If you want to reduce the odds of needing emergency furnace repair, schedule preventative service before the coldest weeks hit. (We offer preventative maintenance and service agreements as part of our heating services.)
Frequently Asked Questions (FAQ’s)
Do you offer 24-hour furnace repair?
Yes—our heating and furnace services include 24-hour emergency repair, along with installation and preventative maintenance.
What areas do you serve near Memphis, IN?
We’re based in Memphis and serve surrounding communities in the region. Our service-area information is available on our website, and we can confirm availability when you call.
Can a dirty filter really shut a furnace down?
Yes. Restricted airflow can cause overheating and trigger safety shutdowns. Filters are one of the first things we recommend checking.
How can I prevent furnace problems during winter?
Change filters regularly, keep vents open and unobstructed, and schedule seasonal maintenance so small issues are found before the furnace is under heavy load.
Schedule Furnace Repair in Memphis, IN With Mitch Craig Heating & Cooling
If your heat is unreliable—or your furnace has stopped working altogether—don’t wait for the problem to get worse. For furnace repair in Memphis, IN, call Mitch Craig Heating & Cooling at (812) 786-0469 to request service. You can also contact us online through our contact page to get on the schedule quickly